Tubing: Difference between revisions
No edit summary |
No edit summary |
||
Line 5: | Line 5: | ||
5/32" Red tubing - 4 ft. needed | 5/32" Red tubing - 4 ft. needed | ||
Installed from the [[Legris]] elbow fittings on the [[HGA]] and the [[Cyclotron]] to the [[Legris]] straight fittings below the [[PPD]]. Also used between the two [[banjo fittings]] on the [[ | Installed from the [[Legris]] elbow fittings on the [[HGA]] and the [[Cyclotron]] to the [[Legris]] straight fittings below the [[PPD]]. Also used between the two [[Legris| banjo fittings]] on the [[trigger tip]]. | ||
1/4" Blue tubing - 2 ft. needed | 1/4" Blue tubing - 2 ft. needed | ||
Installed from the back [[Injector Tube]] to the [[Cyclotron]], from the [[PPD]] to the base of the [[Dale_Resistors| Dale]] RH-50/[[Sage Resistors]] M50W on the [[Ion Arm]] and from the top of the RH-50/[[Sage Resistors]]M50W to the [[Clippard_Instrument_Laboratory_Parts| Clippard]] elbow fitting on the top of the [[Ion | Installed from the back [[Injectors| Injector Tube]] to the [[Cyclotron]], from the [[PPD]] to the base of the [[Dale_Resistors| Dale]] RH-50/[[Sage Resistors]] M50W on the [[Ion Arm]] and from the top of the RH-50/[[Sage Resistors]]M50W to the [[Clippard_Instrument_Laboratory_Parts| Clippard]] elbow fitting on the top of the [[Ion Arm]]. | ||
1/4" Red tubing - 3 ft. needed | 1/4" Red tubing - 3 ft. needed | ||
Installed on the front [[Injector Tube]] to the [[Cyclotron]] and the [[Beam Line]] to the [[Clippard_Instrument_Laboratory_Parts| Clippard]] brass elbow on the [[HGA]] (covered in 1/4" ID split loom) | Installed on the front [[Injectors| Injector Tube]] to the [[Cyclotron]] and the [[Beam Line]] to the [[Clippard_Instrument_Laboratory_Parts| Clippard]] brass elbow on the [[HGA]] (covered in 1/4" ID split loom) | ||
1/4" Green tubing -1 ft. needed | 1/4" Green tubing -1 ft. needed |
Revision as of 00:05, September 6, 2014
Proton Pack Tubing
The actual tubing used on the pack is a contentious issue as are the sizes and lengths used. Here is a basic guideline:
5/32" Red tubing - 4 ft. needed
Installed from the Legris elbow fittings on the HGA and the Cyclotron to the Legris straight fittings below the PPD. Also used between the two banjo fittings on the trigger tip.
1/4" Blue tubing - 2 ft. needed
Installed from the back Injector Tube to the Cyclotron, from the PPD to the base of the Dale RH-50/Sage Resistors M50W on the Ion Arm and from the top of the RH-50/Sage ResistorsM50W to the Clippard elbow fitting on the top of the Ion Arm.
1/4" Red tubing - 3 ft. needed
Installed on the front Injector Tube to the Cyclotron and the Beam Line to the Clippard brass elbow on the HGA (covered in 1/4" ID split loom)
1/4" Green tubing -1 ft. needed
Installed on the gun from the Clippard brass barb on the rear instrument bar to the Clippard brass barb on the rear cylinder.
5/32" Yellow -1 ft. needed
Installed on the Sage 25 resistor on the Ion arm to the Legris elbow fitting on the underside of the Ion Arm.