Screws and Fasteners: Difference between revisions
No edit summary |
No edit summary |
||
Line 1: | Line 1: | ||
These are the Screws and Fasteners that are believed to be used on the Proton Pack. There are different variations for particular fastener types on each of the packs (GB1, GB2, Heroes, SemiHeros, SuperHero, and Stunt) and this is a generalized list. The lengths are unknown. | These are the Screws and Fasteners that are believed to be used on the Proton Pack. There are different variations for particular fastener types on each of the packs (GB1, GB2, Heroes, SemiHeros, SuperHero, and Stunt) and this is a generalized list. The lengths are unknown, however the lengths provided below are a suggestion. | ||
''' | |||
The following list is a generalized list for the GB1 | |||
''' | <big>'''''The following list is a generalized list for the GB1 Proton Pack:'''''</big> | ||
<big>'''Thrower:'''</big> | |||
'''''6-32 socket cap head screws:''''' | |||
Instrument bar | Instrument bar | ||
Barrel lock | Barrel lock | ||
Bottom plate | Bottom plate | ||
Front gun ear | Front gun ear | ||
Gun knub under the brass washers | Gun knub under the brass washers | ||
6-32 flat hex head screws: | |||
'''''6-32 flat hex head screws:''''' | |||
Female V-Hook on Thrower Bracket/Gun Track | Female V-Hook on Thrower Bracket/Gun Track | ||
8-32 cap head screws: | |||
'''''8-32 socket cap head screws:''''' | |||
Thrower Bracket/Gun Track | Thrower Bracket/Gun Track | ||
Screw between the side adjustment knobs | Screw between the side adjustment knobs | ||
4-40 socket cap head screw: | Washer to hold down S-Hook | ||
'''''(Also correct for the bottom plate)''''' | |||
'''''4-40 socket cap head screw:''''' | |||
Top knob | Top knob | ||
''' | '''''Fasteners needed for Thrower:''''' | ||
Larger side knobs | |||
Smaller knob that attaches to larger side knob | |||
Front thrower knob | |||
10-32 cap heads: | Heat sink from inside of Thrower | ||
Larger side knob by Heat sink | |||
Thrower Bracket/Gun Track Disks | |||
<big>'''Proton Pack:'''</big> | |||
'''''4-40 socket cap heads:''''' | |||
2 x 3/8" long for resistors on the Ion Arm. | |||
'''''8-32 socket cap heads:''''' | |||
2 X 1" long for Booster frame (on some packs) | |||
Screw beneath the Ribbon Cable hole ( Spengler pack ) | |||
2 screws X 1" long through the Ribbon Cable Clamp | |||
2 screws through the Clippard valve | |||
'''''10-32 socket cap heads:''''' | |||
2 X 1" long Booster frame (on some packs) | |||
Ion Arm | Ion Arm | ||
4 on the HGA | '''''1/4-20 socket cap head:''''' | ||
4 attaching the bumper (1/4 pan head Phillips on GB2 packs) | |||
4 for attaching the shell to the mobo (1/4 pan head Phillips on GB2 packs) | 4 x 1/4"-1/2" on the HGA | ||
4 x 1 1/2"+ attaching the bumper (1/4 pan head Phillips on GB2 packs) | |||
4 x 1 1/4"+ for attaching the shell to the mobo (1/4 pan head Phillips on GB2 packs) | |||
'''''8-32 slotted flat head machine screws:''''' | |||
2 for V-hook Male bracket mounted from inside. | |||
Revision as of 02:57, December 23, 2012
These are the Screws and Fasteners that are believed to be used on the Proton Pack. There are different variations for particular fastener types on each of the packs (GB1, GB2, Heroes, SemiHeros, SuperHero, and Stunt) and this is a generalized list. The lengths are unknown, however the lengths provided below are a suggestion.
The following list is a generalized list for the GB1 Proton Pack:
Thrower:
6-32 socket cap head screws:
Instrument bar
Barrel lock
Bottom plate
Front gun ear
Gun knub under the brass washers
6-32 flat hex head screws:
Female V-Hook on Thrower Bracket/Gun Track
8-32 socket cap head screws:
Thrower Bracket/Gun Track
Screw between the side adjustment knobs
Washer to hold down S-Hook
(Also correct for the bottom plate)
4-40 socket cap head screw:
Top knob
Fasteners needed for Thrower:
Larger side knobs
Smaller knob that attaches to larger side knob
Front thrower knob
Heat sink from inside of Thrower
Larger side knob by Heat sink
Thrower Bracket/Gun Track Disks
Proton Pack:
4-40 socket cap heads:
2 x 3/8" long for resistors on the Ion Arm.
8-32 socket cap heads:
2 X 1" long for Booster frame (on some packs)
Screw beneath the Ribbon Cable hole ( Spengler pack )
2 screws X 1" long through the Ribbon Cable Clamp
2 screws through the Clippard valve
10-32 socket cap heads:
2 X 1" long Booster frame (on some packs)
Ion Arm
1/4-20 socket cap head:
4 x 1/4"-1/2" on the HGA
4 x 1 1/2"+ attaching the bumper (1/4 pan head Phillips on GB2 packs)
4 x 1 1/4"+ for attaching the shell to the mobo (1/4 pan head Phillips on GB2 packs)
8-32 slotted flat head machine screws:
2 for V-hook Male bracket mounted from inside.
==References==