- December 19th, 2017, 9:17 am#4901754
Hello folks, and welcome to my Proton Pack build thread! This is going to be a slow-burn kinda build as it's my first attempt at prop building and I want to do it right. Also, I'm still putting parts together. My shell and motherboard are from BenofKent Props.
Ben included some very nice resin parts but I want to replace them with aluminum parts so those will end up being sold off at some point. I'm going for a GB1 build with an "accuracy vs. personal preference" caveat. Even without a full assortment of pack parts I can still pick at things so let's get started!
WE HAVE THE TOOLS, WE HAVE THE TALENT!
PROTON PACK
1 x Alice Pack Frame (GBFans)
1 x Mother Board - BenofKent
1 x Pack Body - BenofKent
1 x Ion Arm
1 x PPD - On order from FreekyGeeky
1 x HGA
1 x HGA Label - FreekyGeeky
1 x Vacuum Tube - FreekyGeeky
1 x Beam Tube - Freeky Geeky
1 x Bumper
1 x Shock Mount Bellow
1 x Booster Frame - BenofKent
2 x Injector Tube
1 x Gun Mount Bracket
1 x Shock Mount
1 x Ion Arm Assembly
2 x Alkon AQ68-P Male Connector
1 x Clippard Valve R-331
3 x Clippard #11752 Hose Barb - GBFans Shop
3 x Clippard #15090 L-Fitting - GBFans Shop
1 x Raytheon Crank Knob #MS91528
1 x Spectra Ribbon Cable
1 x Dale RH-50 Resistor (Long) - I haven't been able to find a Dale RH-50. I was able to track down a Sage M50W so it will have to do for now.
1 x Dale PH-25 Resistor - GBFans Shop
1 x Sage Resistor (Short) - GBFans Shop
3 x #3109 Legris Gray Elbows
2 x #3175 Legris Brass Straight Male Connector
1 x Ribbon Cable Clamp - GBFans Shop
5 x Hex-Head Screws
1 x Ribbon Cable Plate Set
1 x 5/32” Red Tubing 5 Feet - BenofKent
1 x ¼” Blue Tubing 3 Feet - BenofKent
1 x ¼” Red Tubing 4 Feet - BenofKent
1 x 5/32” Yellow Tubing 2 Feet - BenofKent
1 x ¼” Split Loom Tubing 3 Feet - BenofKent
1 x ¾” Split Loom Tubing 7 Feet
1 x Set of Red And Blue Theater Gels for Cyclotron and Power Cell. - BenofKent
1 x Set Of Labels - Ben included some very nice vinyl labels in his kit. I'd like to find metallic labels, though.
1 x Loom Clamp - Bionic Moon Labs
PARTICLE THROWER
1 x Particle Thrower Body - Thrower parts on order from CPU64
2 x Handle Pipes
2 x Grips
1 x Rear Instrument Bar
1 x Front Cylinder
1 x Rear Cylinder
1 x Trigger Tip (Speculated to be a gun trigger, but I doubt it ever was)
1 x Forward Knob (Next to Clippard)
1 x Stream Adjuster Knob
1 x Bottom Cosmetic Knob Large
1 x Bottom Cosmetic Knob Small
2 x Double Disk Drift Velocity Knurled Knobs (On left side of gun)
1 x Clear Acrylic Tube
1 x Clippard Valve R-701
2 x Clippard #11752 Hose Barb - GBFans Shop
1 x Gun Heatsink
3 x Toggle Switch
2 x Button Switch
3 x Light-White
1 x Light-Orange
1 x Light-Red
1 x Light-Grill (This is a white light.)
2 x Nycoil Banjo #55020
1 x Orange Cap
1 x ¼” Green Tubing 1 Foot - BenofKent
1 x 5/32 Red Tubing - BenofKent
1 x Set Of Labels - Again, Ben included a set of vinyl stickers. I want to get some rub-ons for the build, though.
Electronics
1 x Power Meter Light & Cyclotron Light Kit
1 x Particle Thrower Light Kit
1 x Sound Kit
1 x 12V 9800 mAh Battery Pack
1 x WandTip Expansion Kit - Spongeface
1 x White Strobe LED - Spongeface
2 x Speakers of Some Kind
Other Parts
1 x XLR Deluxe Spengler Plate - nstevic01
I'm probably missing some pieces on this list so feel free to let me know if I am! Constructive criticism is always welcome in this build.
Ben included some very nice resin parts but I want to replace them with aluminum parts so those will end up being sold off at some point. I'm going for a GB1 build with an "accuracy vs. personal preference" caveat. Even without a full assortment of pack parts I can still pick at things so let's get started!
WE HAVE THE TOOLS, WE HAVE THE TALENT!
PROTON PACK
1 x Alice Pack Frame (GBFans)
1 x Mother Board - BenofKent
1 x Pack Body - BenofKent
1 x Ion Arm
1 x PPD - On order from FreekyGeeky
1 x HGA
1 x HGA Label - FreekyGeeky
1 x Vacuum Tube - FreekyGeeky
1 x Beam Tube - Freeky Geeky
1 x Bumper
1 x Shock Mount Bellow
1 x Booster Frame - BenofKent
2 x Injector Tube
1 x Gun Mount Bracket
1 x Shock Mount
1 x Ion Arm Assembly
2 x Alkon AQ68-P Male Connector
1 x Clippard Valve R-331
3 x Clippard #11752 Hose Barb - GBFans Shop
3 x Clippard #15090 L-Fitting - GBFans Shop
1 x Raytheon Crank Knob #MS91528
1 x Spectra Ribbon Cable
1 x Dale RH-50 Resistor (Long) - I haven't been able to find a Dale RH-50. I was able to track down a Sage M50W so it will have to do for now.
1 x Dale PH-25 Resistor - GBFans Shop
1 x Sage Resistor (Short) - GBFans Shop
3 x #3109 Legris Gray Elbows
2 x #3175 Legris Brass Straight Male Connector
1 x Ribbon Cable Clamp - GBFans Shop
5 x Hex-Head Screws
1 x Ribbon Cable Plate Set
1 x 5/32” Red Tubing 5 Feet - BenofKent
1 x ¼” Blue Tubing 3 Feet - BenofKent
1 x ¼” Red Tubing 4 Feet - BenofKent
1 x 5/32” Yellow Tubing 2 Feet - BenofKent
1 x ¼” Split Loom Tubing 3 Feet - BenofKent
1 x ¾” Split Loom Tubing 7 Feet
1 x Set of Red And Blue Theater Gels for Cyclotron and Power Cell. - BenofKent
1 x Set Of Labels - Ben included some very nice vinyl labels in his kit. I'd like to find metallic labels, though.
1 x Loom Clamp - Bionic Moon Labs
PARTICLE THROWER
1 x Particle Thrower Body - Thrower parts on order from CPU64
2 x Handle Pipes
2 x Grips
1 x Rear Instrument Bar
1 x Front Cylinder
1 x Rear Cylinder
1 x Trigger Tip (Speculated to be a gun trigger, but I doubt it ever was)
1 x Forward Knob (Next to Clippard)
1 x Stream Adjuster Knob
1 x Bottom Cosmetic Knob Large
1 x Bottom Cosmetic Knob Small
2 x Double Disk Drift Velocity Knurled Knobs (On left side of gun)
1 x Clear Acrylic Tube
1 x Clippard Valve R-701
2 x Clippard #11752 Hose Barb - GBFans Shop
1 x Gun Heatsink
3 x Toggle Switch
2 x Button Switch
3 x Light-White
1 x Light-Orange
1 x Light-Red
1 x Light-Grill (This is a white light.)
2 x Nycoil Banjo #55020
1 x Orange Cap
1 x ¼” Green Tubing 1 Foot - BenofKent
1 x 5/32 Red Tubing - BenofKent
1 x Set Of Labels - Again, Ben included a set of vinyl stickers. I want to get some rub-ons for the build, though.
Electronics
1 x Power Meter Light & Cyclotron Light Kit
1 x Particle Thrower Light Kit
1 x Sound Kit
1 x 12V 9800 mAh Battery Pack
1 x WandTip Expansion Kit - Spongeface
1 x White Strobe LED - Spongeface
2 x Speakers of Some Kind
Other Parts
1 x XLR Deluxe Spengler Plate - nstevic01
I'm probably missing some pieces on this list so feel free to let me know if I am! Constructive criticism is always welcome in this build.
Last edited by H2Ghost on December 30th, 2017, 10:21 am, edited 3 times in total.
twmedford23 liked this