Page 3 of 5

Re: A Noob Build Thread

Posted: April 10th, 2021, 5:02 pm
by l3w1sb159
Thanks,
It's the speaker from the GBfans shop that I've ordered so I assume the 4" template should work.

Re: A Noob Build Thread

Posted: April 17th, 2021, 10:07 am
by l3w1sb159
Big progress.

So I managed to spray over the epoxy welds pretty smoothly. And just like that I'm ready to reassemble this sucker.
Image

So putting it back together had a few speed bumps, a few rounded screws but nothing that couldn't be fixed. I lightly weathered the parts that would usually be aluminium underneath and used a burnt umber wash on the bare metal parts and stickers to give it a used look. I'll be swapping the grey crank knob for a black one and keep the other for a future GB1 pack. Ill put the lenses in once I've sorted out the pack lights and I'm still waiting on the rest of the labels to arrive as well as the electronics.

So until then, at least I have this to look at...
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
:cool:

Re: A Noob Build Thread

Posted: April 17th, 2021, 11:51 am
by Nighty80
Dude, that looks amazing!
Great progress - really been enjoying your build, it's sooo close!

Re: A Noob Build Thread

Posted: April 17th, 2021, 12:20 pm
by l3w1sb159
Thanks, it's been quite the learning curve for my first time building any kind of prop. But as mad as it may seem; I'm already planning and gathering parts for a second pack....

Re: A Noob Build Thread

Posted: April 25th, 2021, 12:22 am
by l3w1sb159
My ThrowingChicken thrower kit got here finally, so now the hard part can commence!
Image
Justin threw in an Afterlife style front grip too, top stuff!
Image

I also ordered the aluminium knobs I was missing, as well as 2 pop catches and some custom banjoes from Freekygeeky which arrived at the same time. As I'm planning on a superhero pack down the line I've made my own nycoil style banjoes as they are like unicorn excrement to find!
Image
Image

The main complication to figure out is the pop mech, as TC's front handle design is slighlty different to most, although it has been made a bit easier now that the grip is now seperate to the handle. I'll be pouring over Freekygeekys installation guide for sure.

Re: A Noob Build Thread

Posted: April 25th, 2021, 6:15 am
by l3w1sb159
Quick question, how does one attach an S hook to the gun track as there is a disc molded into TC's kit where the S hook should go?

Re: A Noob Build Thread

Posted: April 25th, 2021, 6:54 am
by l3w1sb159
Nevermind, with a chisel and some persuasion I managed get the disc off and the s hook on.
Image

Re: A Noob Build Thread

Posted: April 25th, 2021, 11:17 am
by l3w1sb159
Made a fair amount of progress;
Attached the rear handle pending epoxy weld,
Attached instrument bar cover,
Attached rear cylinder and barbs
Attached top knob and side knob,
Attached clippard
Drilled out holes for green lever, hat lights, switches, vent, arco lights, front knob, trigger box,
Drilled and tapped the 2 screws with brass spacers to attach the front handle.
Drilled and tapped the base plate holes , plus attached v hook and s hook
Rounded the heatsink fins for giggles.
Image
Image
Image
Image

Still need to mount the trigger box, which I'm waiting for some 6/32 bolts for and I need to dremel out a part of the inner wall to allow the front knob bolt to sit straight.
Plus grips need attaching; the front one of which needs a channel dremeled out to fit over TC's new handle which has a raised channel on the outside of the handle for wires to be routed through under the grip.

And once again waiting for a few more parts and electronics to be delivered to finish the dry fit of the wand, plus I need the acrylic barrel to sort out the pop mech tube and set up the catch and lever.
:sigh:

Re: A Noob Build Thread

Posted: April 26th, 2021, 12:28 pm
by l3w1sb159
Quite proud of the pop mech levers I made; steel for my current build and brass for a future pack.
Image

Re: A Noob Build Thread

Posted: April 26th, 2021, 1:00 pm
by JWils23
Coming along great! Very cool that the front handle is now a separate piece. Mine was the solid piece which makes routing the ear wiring a little more difficult. But I had a blast putting that kit together and I learned a lot.

Re: A Noob Build Thread

Posted: April 26th, 2021, 1:42 pm
by l3w1sb159
That old front handle was the one thing that had me worried about the kit. It took a bit longer to get my kit while he reworked the design but it was well worth the wait.
Makes the pop mech so much easier to install.

Re: A Noob Build Thread

Posted: April 27th, 2021, 5:57 am
by l3w1sb159
Seeing as I wont be getting my electronics for a while, does anyone know what size switches come with the GBfans wand kit? Wanting to predrill the holes accurately so they can be put straight in as soon as I get them.

Re: A Noob Build Thread

Posted: May 1st, 2021, 10:07 am
by l3w1sb159
A small update

Managed to put together as much of the thrower as I can, apart from the inner pop tube once I get the acrylic tube and the electronics.
Image
Image
Image
Image

I'm thinking I should be able to paint the thrower unless I've missed anything. Plus sorting out the pop tube will be a challenge as the inside diameter of the static centre tube is 7/8 which is the same o/d as the acrylic tube, so full need a 7/8 aluminium tube for the pop tube and somehow attach the acrylic tube to the end of it. I'm thinking a 5/8 hollow dowel to connect the two?

Re: A Noob Build Thread

Posted: May 1st, 2021, 10:52 am
by tobycj
I've got some 5/8" acrylic rod, I can cut you an appropriate length if you want, and drill the centre out too if you need it. Pop me a PM if that'd help bud.

Re: A Noob Build Thread

Posted: May 1st, 2021, 12:13 pm
by l3w1sb159
That would be great.

Re: A Noob Build Thread

Posted: May 7th, 2021, 10:29 am
by l3w1sb159
So a little update.

I've started working on my pop tube, big thanks to tobycj for sending me a custom made acrylic dowel.
Image
Image
So I've drilled and tapped through the pop tube, into the dowel, which will be the same for the frosted barrel once I get it. Using grub screws to secure them and 1 regular bolt to act as the guide. Once I get the frosted barrel I can mark and cut the slit in the static tube and cut the pop tube down to size as needed.
Image

Tobycj drilled a hole for routing the wire for the barrel led through which will require some hackery but should be simple enough. Plus having the guide screw not directly into the frosted barrel should help avoid it cracking, as this dowel is sturdy AF

Re: A Noob Build Thread

Posted: May 7th, 2021, 4:05 pm
by tobycj
Glad it got there OK bud. Look forward to seeing it all come together!

Re: A Noob Build Thread

Posted: May 10th, 2021, 10:34 pm
by l3w1sb159
So I managed to primer my parts before the 2 week straight rain hit.
To try and recreate the look of the original grips I found this Army Painter Fur Brown primer, which hopefully will be close enough in colour for when I come to weather the grips.
Image

Re: A Noob Build Thread

Posted: May 16th, 2021, 2:06 am
by l3w1sb159
A little update.

I managed to squeeze in some painting in between the rain, layed down the silver undercoat and the black top coat.
Image
Image

I left the paint to cure for a day, then I attached the rear handle and made the epoxy fake weld using a paper clip to make the bead. It turned out fairly well.
Image

Just waiting for another break in the weather to paint over the weld and painting will be officially done! In the meantime I've been working on the pop mech....

Re: A Noob Build Thread

Posted: May 21st, 2021, 1:24 pm
by l3w1sb159
Okay, so here is my attempt at a Throwingchicken V4 compatible pop mech.

So once I got my clear acrylic tube, I got it drilled and tapped onto the end of the pop tube dowel, using m3 grub screws again. A little side note the clear acrylic tube from the shop has such crisp lines, top notch.
Image

Next I took the "inner master tube" that came with TC's kit; attached it to the gun body and lined up the pop tube along side to see where the guide slot would need to go. From references I found that, fully extended, the bottom frosted part should be level with the end of the barrel and for the length protruding when fully closed I eyeballed more references, although it was harder without having the trigger tip yet. So after marking the locations for either end of the slot I chain drilled a straight line between the two and filed the rest flat for a snug fit for the 6mm wide bolt head. After a test fit it looks fairly close to me.
Image
Image
Image

Once that was sorted I cut off the excess length from the pop tube, drilled and tapped for a m3 bolt to line up where the pop catch can latch onto, and also cut 4" lengthways similar to Freekygeekys setup to allow the pop tube to miss the barrel lock bolt.
Image
Image

One problem I have encountered is the pop catch I got from freekygeeky doesnt seem to lock onto the 1/8" lever when I screw the small bolt in. It seems to not thread slightly into the hole where the lever goes through as I would assume it should?. Not sure of what to do to fix the catch to the lever as it can still spin freely from the lever even when the bolt is fully screwed in?
Image

While I was at it, I thought I would put as much of the thrower back together as I could, so here's where I'm at right now...
Image
Image
Image

Re: A Noob Build Thread

Posted: May 21st, 2021, 10:25 pm
by JWils23
I would message RJ about that catch, it should definitely feed into the lever hole so that it locks in and doesn’t flow freely. I have the same steel catch and it is visible in that hole and locks to the lever.

Coming along great beyond that though, thrower is a beauty!

Re: A Noob Build Thread

Posted: May 22nd, 2021, 4:03 am
by l3w1sb159
Thanks man, I appreciate it.

And I thought that, ill see if RJ has any solutions.

Just the agonising wait for stuff to clear customs again.

Re: A Noob Build Thread

Posted: May 22nd, 2021, 9:37 pm
by JWils23
I get it, I’m sure it’s taking forever to get things across the pond now. If it makes you any feel better I had to file my steel catch for probably close to 40 minutes to get it to the point where it would catch the screw on the pop mech. The aluminum one I had was dead on, but the steel one was cut just a bit short. So while yours won’t screw in, mine wouldn’t catch. Seems like the steel catches may still need a little tweaking on RJ’s side.

Re: A Noob Build Thread

Posted: May 23rd, 2021, 12:11 am
by l3w1sb159
Ah yes, I'm also part of the "40 minute filing club". Such a minor thing but is hell on your hands. Apart from this one problem the rest of RJ's stuff I've ordered has been top notch.

Re: A Noob Build Thread

Posted: May 23rd, 2021, 11:52 am
by JWils23
Ah so it looks like there's a common issue here. That honestly surprises me because I've never had a fitment issue with anything from RJ, other than maybe some incredibly minor filing to get a particular fit or detail that I wanted. But yea this catch really needed some work, and it took a lot of filing and then testing and filing again before I finally got it where I wanted it. I could have just used the aluminum one but I like the feel of the steel one better so in the end it was worth it.

Re: A Noob Build Thread

Posted: May 23rd, 2021, 2:36 pm
by l3w1sb159
I saw on the pop mech install tutorial on his website that some filing might be needed so I was kind of prepared ^^
I am still definitely going to go with him for my next full thrower though, it would be a lot less faff having a proper aluminium wand rather than resin.

Re: A Noob Build Thread

Posted: May 28th, 2021, 12:52 am
by l3w1sb159
Hey guys, exciting times as my wand light kit was delivered the other day!
Two questions; what reflector is best to use to mount the vent light led in under the vent slits? I assume a square one but I'm not sure where to find the right size and shape.
Also what cables will I need to wire up my speaker to the soundboard (it's the gbfans shop speaker)

Re: A Noob Build Thread

Posted: May 28th, 2021, 2:16 am
by tobycj
The screen used reflectors were round, not square :) Dan.aka previously recommended a "metal replacement cone for a Fulton MX-991/U angle head torch" to me for that, but they seem to be hard to come by in the UK, so I think any similar military torch reflector would probably work ok. I picked a whole torch up for a fiver a on eBay a couple of years ago.

Re: A Noob Build Thread

Posted: May 28th, 2021, 2:28 am
by l3w1sb159
Ah right, I'm wondering what depth it would need to be as it's quite tight for space inside.

Re: A Noob Build Thread

Posted: May 28th, 2021, 2:43 am
by l3w1sb159
This post may contain an affiliate link that helps support GBFans.com when you make a purchase at no additional cost to you.

I've had a look and found something, want to double check it's the right kind of reflector...
https://www.ebay.co.uk/itm/372436495752