Page 2 of 3

Re: My Anovos proton pack build

Posted: February 9th, 2018, 7:01 pm
by Sailerm
Image
Dummy mock up of the Lights. First off the power meter lights are bigger than the window for them but it's ok. The only real draw back is the power leads for the system comes off the top so I'll have to solder leads to put them where I want

Re: My Anovos proton pack build

Posted: February 13th, 2018, 2:14 pm
by livewire008
Very nice work, man.

Still holding my breath for my kit... ordered October 2016, so hopefully I'll get an email any day now. In the meantime, I'm planning where I want things to go. Just got an Alice frame (not the Anovos one; got tired of waiting for them and ordered from the shop here) getting a real feel for the frame dimensions will inform where I decide to put my motherboard holes for the electronics.

Re: My Anovos proton pack build

Posted: February 13th, 2018, 8:46 pm
by Sailerm
I'm still waiting for the Alice frame as well

Re: My Anovos proton pack build

Posted: February 14th, 2018, 10:43 am
by Marcus B
Has anyone seen the alice frame? Might be worth just grabbing one from a surplus store and not waiting. Anovos should be able to churn those out quickly I'd think seeing as companies still make them..

Re: My Anovos proton pack build

Posted: February 20th, 2018, 10:20 am
by Xavierallen
livewire008 wrote:Very nice work, man.

Still holding my breath for my kit... ordered October 2016, so hopefully I'll get an email any day now. In the meantime, I'm planning where I want things to go. Just got an Alice frame (not the Anovos one; got tired of waiting for them and ordered from the shop here) getting a real feel for the frame dimensions will inform where I decide to put my motherboard holes for the electronics.
I ordered mine March of 2017...still no word on shipment date...meh

Re: My Anovos proton pack build

Posted: February 20th, 2018, 6:48 pm
by Sailerm
I decided to use an existing frame I had in the garage rather than wait for the Anovos frame.

Though upgrades and modifications will continue, I am calling my pack finished. Image

Re: My Anovos proton pack build

Posted: February 20th, 2018, 6:49 pm
by Sailerm
Image
Here you can see the small switch the powers the lights.

Re: My Anovos proton pack build

Posted: February 20th, 2018, 6:51 pm
by Sailerm
Image

The original top bolt was too low causing a lot of flex on the plastic motherboard so I
Added a second bolt with spacer up higher (where it should have been originally). The additional bolt makes the pack much more rigid

Re: My Anovos proton pack build

Posted: February 20th, 2018, 6:53 pm
by Sailerm
Image

Here you can see I have 2 center bolts as well as the two lower bolts.

3/8" x 1/2 stainless lag bolts with wide washers on both inside and outside the mother board with stainless spacers

Re: My Anovos proton pack build

Posted: February 22nd, 2018, 6:30 pm
by Sailerm
Image

Re: My Anovos proton pack build

Posted: March 5th, 2018, 7:33 pm
by Sailerm
Image
Rox is working on her pack now. It Tucker's her out

Re: My Anovos proton pack build

Posted: March 5th, 2018, 7:34 pm
by Sailerm
Image

Re: My Anovos proton pack build

Posted: March 20th, 2018, 4:00 pm
by doctorevil30564
Your pack looks great!

Re: My Anovos proton pack build

Posted: March 24th, 2018, 2:22 pm
by Sailerm
Adding GBfans wand lights to Roxane's Anovos pack. Anyone have a good photo of how the ear button and light would be wired and mounted?

Re: My Anovos proton pack build

Posted: March 24th, 2018, 4:15 pm
by feevrt
This is how I did mine -

I started by drilling down from the top of the ear, straight through to the other side. I chose a bit that was the same width of the starter holes for the Anovos-supplied parts.

For the hole with the switch, drilled again down from the top with a bit the same width as the threads on the switch. Next, I chose a drill bit wide enough that the kit switch could fit easily in the hole it would drill. I then started drilling very carefully from the bottom until the hole was just deep enough that the threads protruded enough to screw the nut on the switch. At times, I was allowing the drill the turn only once between test fittings.

The switch went deep enough into the body of the ear that I had to cut a channel in between the holes so that the light could be inserted sufficiently deep into its hole. In the pic below, you can see where the Dremel cutting wheel got away from me - I'll have to fix that at some point ;)

For the wire routing, I drilled a hole in the clear emitter tube and ran the plug down to the control board. Because the tube is so brittle, I covered the area I was going to drill with masking tape and started with a small bit. I worked my way up drill bit sizes until I had a hole just large enough for the plug.

Hope this helps.

Bottom view:
Image

Top view:
Image

Re: My Anovos proton pack build

Posted: March 25th, 2018, 12:50 pm
by Sailerm
feevrt wrote:This is how I did mine -

I started by drilling down from the top of the ear, straight through to the other side. I chose a bit that was the same width of the starter holes for the Anovos-supplied parts.

For the hole with the switch, drilled again down from the top with a bit the same width as the threads on the switch. Next, I chose a drill bit wide enough that the kit switch could fit easily in the hole it would drill. I then started drilling very carefully from the bottom until the hole was just deep enough that the threads protruded enough to screw the nut on the switch. At times, I was allowing the drill the turn only once between test fittings.

The switch went deep enough into the body of the ear that I had to cut a channel in between the holes so that the light could be inserted sufficiently deep into its hole. In the pic below, you can see where the Dremel cutting wheel got away from me - I'll have to fix that at some point ;)

For the wire routing, I drilled a hole in the clear emitter tube and ran the plug down to the control board. Because the tube is so brittle, I covered the area I was going to drill with masking tape and started with a small bit. I worked my way up drill bit sizes until I had a hole just large enough for the plug.

Hope this helps.

Bottom view:
Image

Top view:
Image
Awesome. Thank you.

Re: My Anovos proton pack build

Posted: March 25th, 2018, 2:56 pm
by feevrt
My pleasure. Your pics were a big help to me as I was working on my build, so I'm happy to return the favor.

Re: My Anovos proton pack build

Posted: March 25th, 2018, 4:05 pm
by Sailerm
Image
I drilled out Roxane's just like you did yours. I'm still debating as to where to drill a hole in the barrel to hide the wiring harness. I seem to recall some packs ride them exposed along the barrel of the wand.

Re: My Anovos proton pack build

Posted: March 25th, 2018, 4:06 pm
by Sailerm
Image

Re: My Anovos proton pack build

Posted: March 25th, 2018, 4:07 pm
by Sailerm
Image

Re: My Anovos proton pack build

Posted: March 25th, 2018, 6:16 pm
by feevrt
I thought about routing on the outside, too. I didn't see a good unobtrusive way to do it and I didn't want to cut an access into the inside of the wand to route the plug and wires. In the end, I thought that drilling the tube was the less risky/best looking option, even taking into account the brittleness of the transparent plastic.

Re: My Anovos proton pack build

Posted: March 26th, 2018, 4:21 pm
by Sailerm
Image
I decided to dremel out a channel next to the molded in hand grip and e6000 the wires into it. I'll most likely hit it lightly with a touch of paint to de-emphasize it when dry.
Image

Re: My Anovos proton pack build

Posted: March 28th, 2018, 1:31 pm
by Sl!mer
Kingpin wrote: February 9th, 2018, 12:12 pm As for mounting, some folks mount flashlight reflectors to the shell, and fix the LEDs to the reflectors:
Where did you purchase your reflectors and frosted glass?

Re: My Anovos proton pack build

Posted: March 28th, 2018, 3:14 pm
by Kingpin
My reflectors came from cheap torches that I bought at a British dollar store. The torches in question though were bulb rather than LED ones, which may have a more specially-molded reflector... Definitely check before purchasing, especially if your Pack lights featured clustered LEDs for the Cyclotron lights, rather than a single LED (which is what mine had).

I didn't have frosted acrylic on mine on my first Pack, but you could either purchase pre-frosted acrylic on eBay, or a frosted finish spray paint from a paint specialist. :)

Re: My Anovos proton pack build

Posted: March 29th, 2018, 12:23 pm
by Sl!mer
Sailerm wrote: March 25th, 2018, 4:05 pmImage
I'm still debating as to where to drill a hole in the barrel to hide the wiring harness. I seem to recall some packs ride them exposed along the barrel of the wand.
I won't be receiving my sound/light kit till July, but I'm already researching what I'm going to do. What I'm thinking of doing is drilling a hole into the barrel and then covering the remaining exposed wiring with epoxy.

Re: My Anovos proton pack build

Posted: April 2nd, 2018, 7:22 am
by Sailerm
I'm going to throw Rox under the bus. When both packs came in, she was clear that she wanted to build her own pack but dragged her feet. She's lost interest in the build and has asked me to take over.

Re: My Anovos proton pack build

Posted: April 2nd, 2018, 5:58 pm
by deadderek
I'd say "ok"...then order a Spirit pack and give it to her. :lol::lol::lol::lol::lol::lol::lol::lol::lol::lol::lol::lol::lol:

Re: My Anovos proton pack build

Posted: April 3rd, 2018, 7:15 pm
by Sailerm
Image
Image
Rox's is about half done

Re: My Anovos proton pack build

Posted: April 4th, 2018, 7:35 am
by Xavierallen
My god those look nice! I can't wait for mine to be delivered....in 13 years....i laugh, but with sad tears.

Re: My Anovos proton pack build

Posted: April 4th, 2018, 2:15 pm
by Sailerm
I'm still waiting for the Alice frames. I used one I already had for mine but unless I buy one from someone that has them instock, I'll wait for Anovos. Well actually I'll wait a little longer but leave myself some time before Denver Comic con so I can complete Roxane's.