- October 31st, 2009, 2:02 pm#179079
So after serching for quiet some time I could not find a good list that told the names of the parts you need to build a Proton Pack and Particle Thrower. So I made a list myself. First let me say that there maybe something missing from here so do your own double checking, but I'm sure that the numbers are correct as for how many of each part you need(if your building more then one pack multiply the parts on the list accordingly. 2 Alice frames = 2 packs, 4 injector tubes = 2 packs and so on). Next I did add an extra foot to all the tubing measurements so you have some extra length to use or in case you make a mistake. Here is the list as follows I hope everybody finds it useful. Good luck with your build.
PROTON PACK
1 x Alice Pack Frame
1 x Mother Board
1 x Pack Body
1 x Power Cell
1 x Ion Arm (GBFans Shop)
1 x Booster
1 x PPD Box + Cy1inder
1 x Crank Generator
1 x HGA
1 x Sync Generator
1 x Cyclotron
1 x Bumper
1 x N-Filter
1 x Shock Mount Bellow
1 x Booster Frame (GBFans Shop)
2 x Injector Tube
1 x Gun Mount Box
1 x Gun Mount Dixie Cup Bracket (GBFans Shop)
1 x Shock Mount
1 x Ion Arm Assembly (GBFans Shop: GB1, GB2)
2 x Alkon AQ68-P Male Connector
1 x Clippard Valve R-331
3 x Clippard #11752 Hose Barb (GBFans Shop)
3 x Clippard #15090 L-Fitting (GBFans Shop)
1 x Raytheon Crank Knob #MS91528 (GB Gray GB2 Black)
1 x Spectra Ribbon Cable
1 x Dale RH-50 Resistor (Long) (GBFans Shop)
1 x Dale PH-25 Resistor (GBFans Shop)
1 x Sage Resistor (Short) (GBFans Shop)
3 x #3109 Legris Gray Elbows
2 x #3175 Legris Brass Straight Male Connector
1 x HGA Pipe/End-Caps 2.37x2.5
1 x Ribbon Cable Clamp (GBFans Shop)
5 x Hex-Head Screws
1 x Ribbon Cable Plate Set (GBFans Shop)
1 x Power Meter Light & Cyclotron Light Kit
1 x Sound Kit
1 x 5/32” Red Tubing 5 Feet (GBFans Shop)
1 x ¼” Blue Tubing 3 Feet (GBFans Shop)
1 x ¼” Red Tubing 4 Feet (GBFans Shop)
1 x 5/32” Yellow Tubing 2 Feet (GBFans Shop)
1 x ¼” Split Loom Tubing 3 Feet (GBFans Shop)
1 x ¾” Split Loom Tubing 7 Feet (GBFans Shop)
1 x Set of Red And Blue Theater Gels for Cyclotron and Power Cell.
1 x Set Of Labels
PARTICLE THROWER
1 x Particle Thrower Body
2 x Handle Pipes
2 x Grips
1 x Rear Instrument Bar
1 x Front Cylinder
1 x Rear Cylinder
1 x Trigger Tip (Speculated to be a gun trigger, but I doubt it ever was)
1 x Forward Knurled Knob (Next to Clippard)
1 x Knurled Stream Adjuster Knob
1 x Bottom Cosmetic Knob Knurled Large (On right side of gun behind Heatsink)
1 x Bottom Cosmetic Knob Knurled Small (On right side of gun behind Heatsink)
2 x Double Disk Drift Velocity Knurled Knobs (On left side of gun)
1 x Clear Acrylic Tube
1 x Clippard Valve R-701
2 x Clippard #11752 Hose Barb (GBFans Shop)
1 x Gun Heatsink
3 x Toggle Switch
2 x Button Switch
3 x Light-White (These are different so pay close attention to the reference pics!)
1 x Light-Orange
1 x Light-Red
1 x Light-Grill (This is a white light.)
2 x Nycoil Banjo #55020
1 x Orange Cap
1 x ¼” Green Tubing 1 Foot (You won’t need that much, better to have a little extra) GBFans Shop
1 x 5/32 Red Tubing (You should have some of this left over from the Proton Pack)
1 x Light Kit
1 x Set Of Labels
Connect to Proton Pack using ¾” Split Loom Tubing.
PROTON PACK
1 x Alice Pack Frame
1 x Mother Board
1 x Pack Body
1 x Power Cell
1 x Ion Arm (GBFans Shop)
1 x Booster
1 x PPD Box + Cy1inder
1 x Crank Generator
1 x HGA
1 x Sync Generator
1 x Cyclotron
1 x Bumper
1 x N-Filter
1 x Shock Mount Bellow
1 x Booster Frame (GBFans Shop)
2 x Injector Tube
1 x Gun Mount Box
1 x Gun Mount Dixie Cup Bracket (GBFans Shop)
1 x Shock Mount
1 x Ion Arm Assembly (GBFans Shop: GB1, GB2)
2 x Alkon AQ68-P Male Connector
1 x Clippard Valve R-331
3 x Clippard #11752 Hose Barb (GBFans Shop)
3 x Clippard #15090 L-Fitting (GBFans Shop)
1 x Raytheon Crank Knob #MS91528 (GB Gray GB2 Black)
1 x Spectra Ribbon Cable
1 x Dale RH-50 Resistor (Long) (GBFans Shop)
1 x Dale PH-25 Resistor (GBFans Shop)
1 x Sage Resistor (Short) (GBFans Shop)
3 x #3109 Legris Gray Elbows
2 x #3175 Legris Brass Straight Male Connector
1 x HGA Pipe/End-Caps 2.37x2.5
1 x Ribbon Cable Clamp (GBFans Shop)
5 x Hex-Head Screws
1 x Ribbon Cable Plate Set (GBFans Shop)
1 x Power Meter Light & Cyclotron Light Kit
1 x Sound Kit
1 x 5/32” Red Tubing 5 Feet (GBFans Shop)
1 x ¼” Blue Tubing 3 Feet (GBFans Shop)
1 x ¼” Red Tubing 4 Feet (GBFans Shop)
1 x 5/32” Yellow Tubing 2 Feet (GBFans Shop)
1 x ¼” Split Loom Tubing 3 Feet (GBFans Shop)
1 x ¾” Split Loom Tubing 7 Feet (GBFans Shop)
1 x Set of Red And Blue Theater Gels for Cyclotron and Power Cell.
1 x Set Of Labels
PARTICLE THROWER
1 x Particle Thrower Body
2 x Handle Pipes
2 x Grips
1 x Rear Instrument Bar
1 x Front Cylinder
1 x Rear Cylinder
1 x Trigger Tip (Speculated to be a gun trigger, but I doubt it ever was)
1 x Forward Knurled Knob (Next to Clippard)
1 x Knurled Stream Adjuster Knob
1 x Bottom Cosmetic Knob Knurled Large (On right side of gun behind Heatsink)
1 x Bottom Cosmetic Knob Knurled Small (On right side of gun behind Heatsink)
2 x Double Disk Drift Velocity Knurled Knobs (On left side of gun)
1 x Clear Acrylic Tube
1 x Clippard Valve R-701
2 x Clippard #11752 Hose Barb (GBFans Shop)
1 x Gun Heatsink
3 x Toggle Switch
2 x Button Switch
3 x Light-White (These are different so pay close attention to the reference pics!)
1 x Light-Orange
1 x Light-Red
1 x Light-Grill (This is a white light.)
2 x Nycoil Banjo #55020
1 x Orange Cap
1 x ¼” Green Tubing 1 Foot (You won’t need that much, better to have a little extra) GBFans Shop
1 x 5/32 Red Tubing (You should have some of this left over from the Proton Pack)
1 x Light Kit
1 x Set Of Labels
Connect to Proton Pack using ¾” Split Loom Tubing.
"What about the Twinkie?" - Dr. Peter Venkman